Samsung Washing Machine Won’t Spin No Error Code | Fast Fixes

If your Samsung drum stays still yet the panel shows no warning, the cause is usually simple: the load is off-balance, the washer can’t drain, a setting is blocking spin, or the machine needs a quick recalibration. This guide gives clear, hands-on steps you can do at home before calling for service. You’ll find fast checks first, then deeper fixes with photos and button combos you can try on most models.

Quick Checks Before You Start

Work through these short checks in order. Most no-code spin problems clear here.

Symptom	What To Check	Action
Drum won’t spin at all	Drain status, standing water, pump sounds	Open the pump filter hatch on front-load models and drain any water, then clean the filter and restart.
Wring-wet laundry	Load balance and size	Break up tangles, add or remove items to even weight, then run Spin Only.
Buttons seem dead	Child Lock / key icon	Turn off Child Lock using the two-button combo on your panel.
Cycle ends with clothes soaked	Spin setting	Make sure “No Spin” isn’t selected; choose a higher spin speed or run Spin Only.
Long cycle / pauses but no code	Suds level	Use HE detergent only; if over-suds, run Rinse+Spin and reduce soap next wash.
Stops mid-spin	Washer leveling and floor bounce	Adjust leveling feet; the tub should sit steady with a small push.
Drains slowly	Drain hose height and kinks	Set hose depth to about 6–8 inches in the standpipe; straighten bends.

Samsung Washer Not Spinning With No Code — Common Causes

Below are the most likely culprits when the panel stays quiet. Each fix includes the exact action to take on a Samsung washer, plus a way to confirm it worked.

1) The Load Is Out Of Balance

Single bathmats, a lone duvet, or a tight tangle can make the tub bounce. The control may quietly slow or skip spin to protect the motor. Open the door, shake items loose, add a few light pieces to even the weight, and try Spin Only. Avoid running a single heavy piece alone; pair it with similar items for balance.

2) The Washer Can’t Drain Fast Enough

Spin won’t start until water leaves the tub. On front-loaders, open the lower access door, pull the emergency drain tube, empty the water into a tray, then unscrew and clean the pump filter. Remove lint, hair, coins, and check that the impeller behind the filter turns freely. Refit the cap and filter snugly, close the door, and run Drain/Spin. Samsung’s support shows the access door location and drain steps for the debris filter on front-load models (debris filter guide).

Set The Drain Hose Correctly

Insert the hose 6–8 inches into the standpipe and keep it free of kinks. Too shallow can cause splash and slow drain; too deep can siphon water back in. Samsung’s guidance calls out the same depth range and avoiding airtight seals on the pipe bend (no-spin solutions).

3) A Setting Is Blocking Spin

• Child Lock (CL): If CL or a lock icon shows, button presses won’t change the cycle. Turn Child Lock off using the two-button combo printed near the icons; buttons vary by panel, and Samsung’s help page walks through the feature and how to disable it (Child Lock help).
• No Spin or Rinse Hold: Some panels let you choose “No Spin” or pause with water after the final rinse. Press Spin to select a spin speed (Low/Med/High) and confirm on the display. If your model supports it, hold Spin for ~3 seconds to enter Spin Only mode.
• Delay End: Delay End shifts the start time so a cycle finishes later. If the tub looks idle with time on the clock, cancel Delay End and restart.

4) Over-Suds From The Wrong Detergent

Too many bubbles keep clothes floating, so the tub can’t wring water out. Use HE-marked detergent only and measure lightly. Samsung explains that a SUD/SUdS condition pauses the cycle until foam drops, then the cycle resumes (SUDS code info). If you see lots of foam, run Rinse+Spin, then reduce dose next time.

5) The Machine Needs Calibration

After installation, moving, or clearing a blockage, the weight sensor can be slightly off. Calibration tunes the sensor with an empty drum so spin logic works right. On many panels, power on, then hold Temp + Delay End for ~3 seconds until “Cb” appears; press Start/Pause and wait as the drum turns slowly for a few minutes. Samsung’s article shows the steps and button names by region and panel style (Calibration guide).

6) The Cycle Type Limits Spin

Delicate cycles may cap speed. If clothes come out wet, change to a program with higher spin or run Spin Only right after the wash. Samsung’s cycle reference confirms a Spin Only option on many models and the long-press Spin button shortcut on some panels (cycle reference).

Step-By-Step Fix: From Easiest To Deep

Step 1 — Power Cycle And Recheck Spin Setting

1. Turn the washer off at the button, wait 30 seconds, then power back on.
2. Choose a cycle with a high spin speed. If the panel shows “No Spin,” change it.
3. If available, hold Spin for ~3 seconds to enter Spin Only. Start the cycle and watch the timer appear, which confirms the mode took effect.

Step 2 — Rebalance The Load

1. Open the door and loosen any tight braid of sheets or jeans.
2. Add 1–3 light towels if you were washing a single heavy item; remove items if the drum is packed tight.
3. Close the door and run Spin Only to test.

Step 3 — Clear Water And Clean The Pump Filter (Front-Load)

1. Place a towel and a low tray at the lower access door.
2. Open the door, pull the small drain tube, and empty the water.
3. Unscrew the large filter. Rinse lint and grit, check the impeller behind it, then reinstall firmly.
4. Close the door and run Drain/Spin to confirm a strong drain and full-speed spin. The method matches Samsung’s debris filter instructions for front-load designs (see the linked debris filter guide above).

Step 4 — Fix The Drain Hose Path

1. Make sure the hose isn’t kinked or crushed behind the cabinet.
2. Insert the hose about 6–8 inches into the standpipe and secure it; avoid taping it airtight.
3. Run Rinse+Spin. If the tub drains quickly and the time counts down steadily, the path is clear. Samsung’s no-spin solutions page outlines the same hose depth and kink checks (linked above).

Step 5 — Turn Off Child Lock And Any Hold States

1. If CL or a lock icon shows, hold the two labeled buttons for about 3 seconds until the icon turns off.
2. If Rinse Hold is active, run Drain/Spin to empty the tub, then choose a normal cycle with spin.

Step 6 — Run Calibration Mode

1. Remove all laundry; the drum must be empty.
2. Power on. Hold Temp + Delay End for about 3 seconds until “Cb” appears.
3. Press Start/Pause. The drum rotates slowly for a few minutes and stops at 0.
4. Run Spin Only to confirm you get a firm ramp-up to speed.

Step 7 — Confirm Detergent Type And Dose

Use HE detergent only. Fill only to the line for your load size. Pods go straight in the drum. Samsung’s care page gives clear placement and dosing tips for both front- and top-load drawers (detergent use).

When The Drum Still Refuses To Spin

If none of the steps above restore spin and no code appears, you may be looking at a part that needs service: a worn belt, a faulty door-lock switch, or a motor control problem. Samsung’s “does not spin at all” page lists motor service as a possibility and also points back to drain and calibration checks first (no-spin troubleshooting). If your model shows any code later, look it up in Samsung’s error guide to pinpoint the path forward.

Useful Panel Actions You Can Try

Many Samsung panels share handy shortcuts. Here are two actions that help when spin misbehaves:

Run Spin Only

On many models, press and hold Spin for ~3 seconds until a time appears, choose the spin speed, then press Start/Pause. This is handy after rebalancing a load or clearing the filter (Samsung documents the long-press method on its cycle reference page linked earlier).

Run Rinse + Spin

This clears soap and stabilizes a mixed load. It’s the fast way to chase suds out of the tub after an over-dose, which can quietly block spin.

Common Button Combos For Spin Only And Calibration

Panel Style	Spin Only	Calibration
Front-load (many models)	Hold Spin ~3 sec until time shows, pick speed, press Start/Pause.	Power on, hold Temp + Delay End ~3 sec until “Cb”, press Start/Pause.
Top-load (select models)	Press Spin, then Start/Pause to run a short spin; adjust time if allowed.	Power on, hold two labeled buttons (often Temp + Delay End) ~3 sec, then Start/Pause.
AI/Smart panels	Select Drain/Spin in the cycle list or long-press Spin if supported.	Follow the on-screen “Calibration” prompt in Settings or use the button combo above.

Care Habits That Keep Spin Reliable

Clean The Pump Filter Every Few Months (Front-Load)

Make this a regular task. A clean filter keeps the drain fast and the spin strong. Samsung recommends periodic cleaning; the linked guide at the top shows each step and the small drain tube you’ll use to empty water first.

Dose HE Detergent Lightly

Too much soap lowers spin results and stretches cycle time. Use the measuring lines on the cap, and pick HE formulas only. If you see bubbles in the glass near the end of a cycle, cut back next time.

Level The Cabinet

Turn the front feet to stop wobble. A stable base reduces auto-corrections that can skip spin without throwing a code.

Mind The Hose Height

Keep that 6–8 inch insertion depth and a smooth arc behind the washer. This simple setup keeps water flowing out at full rate.

What If A Code Finally Shows Up?

If a symbol appears later (Ub/Ur/UE for balance, 5C/5E for drain, SUd/SUD for soap), use Samsung’s code pages for model-specific steps. Ur often means the washer is adding water and trying again, which can extend cycle time; that’s normal behavior when a load needs a rebalance.

Wrap-Up: Your Fast Action Plan

1. Set a real spin speed or use Spin Only.
2. Rebalance the load with a few extra items or by loosening tangles.
3. Drain and clean the pump filter; set the hose to 6–8 inches in the standpipe.
4. Turn off Child Lock and clear any hold state.
5. Run Calibration with an empty drum.
6. Switch to HE detergent and lighten the dose.

Those steps resolve most no-code spin issues on Samsung washers. If the drum still won’t move, the brand’s support page notes that motor service may be needed after you rule out drain and calibration. At that point, grab your model number from the door label and contact support with the notes from your tests.